Prime Parquet Varnish

One component water-based parquet varnish
General Information
Prime Parquet Varnish is a one-component, water-based varnish with high scratch and abrasion resistance developed for the maintenance of your wooden floorings.
General Features
  • Odorless
  • Hard and durable
  • High abrasion and scratch resistance
  • Easy maintenance
  • Lead-free
  • Environmentally friendly
  • Ready to use
Where to Use
  • Wooden floors.
Packaging
  • 5 L.
  • 10 L. (Produced on order basis)
Color Chart

Semi-Matt

High Gloss

Warning:

The above colors are applied on pine and are intended to approximate the final color. The color obtained will vary according to the type, texture and the absorbency of the wood. To see the final color, it is recommended to apply the coating on the wood to be actually used.

 

 

Surface Preparation

 

 

 

  • Do not use products like cellulose or polyurethane filler or primer before the application of the product. As a filler, mix the wood dust with the product and fill all gaps and joints of the parquet. Clean the excess paste after it has dried out.
  • New Wooden Floors: o Clean the surface completely. o Sand the surface with parquet sanding machine or hand using sandpaper #120/150. o Thoroughly clean the generated dust and remove it completely from the surface with a vacuum cleaner. o Prime Decorative Colorant can be used for coloring the parquet floor. After the coloring, allow at least 6 hours to dry before the varnish application.
  • Varnished Wooden Floors: o Remove the old varnish from the parquet completely with a scraping machine. Remove any dirt, oil, wood dust, and old varnish residues from the surface. o Thoroughly clean the generated dust and remove it completely from the surface with a vacuum cleaner. o Remove the remaining dust with a damp cloth. 
Application
  • The product is ready to use and does not require thinning. (At very high temperatures 2-3% drinking water may be added).
  • Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
  • Apply the 1st coat by a brush or roller and leave it to dry for 2 hours.
  • Perform a slight sanding with sandpaper #180/220 before applying the 2nd coat.
  • Apply the 2nd and 3rd coats in 2 hours intervals by sanding with sandpaper #180/220 between the coats.
  • For any reason, if 8 hours exceeded between coats, wait 24 hours and sand the surface with sandpaper #220/240 (aluminum oxide or silicon carbide type sandpaper is recommended) before applying the next coat.
  • Apply the 1st varnish coat first across the grain and then along the grain to leave equal and sufficient amount on the parquet surface without sweeping too much.
  • The area should be ventilated after the application to promote the drying.
  • Allow 7 days for full cure. 
Maintenance
  • Do not apply the product directly on pre-coated surfaces.
  • Remove the old varnish from the parquet completely with a scraping machine. Remove any dirt, oil, wood dust and old varnish residues from the surface.
  • Thoroughly clean the generated dust and remove it completely from the surface with a vacuum cleaner.
  • Remove the remaining dust with a damp cloth.
  • Repeat the same process as described in “Application” with 3 coats.
  • Inspect annually and maintain as required.
Information
  • FOR INTERIOR USE ONLY.
  • Do not apply products such as nitro, polyurethane basecoats or primers before Prime Parquet Varnish.
  • Keep the product closed when not in use.
  • The general application temperature of the product is between 15°C. to 25°C. at a relative humidity range of 40-65%.
  • The moisture content of the wood should be below 12%.
  • The area should be ventilated during and after the application to promote the drying.
  • The product should not be applied when the weather or surface temperature is below 10°C.
  • The varnished floor should not be cleaned with ammonia containing cleaning materials.
  • The varnished floor can be stepped on after 24 hours. Allow 7 days before spreading carpet and/or cleaning.
  • The product should be protected from freezing and stored at temperatures between 5°C to 35°C.
  • Painting tools should be cleaned with soap and plenty of warm water after application.
General Instructions

For product application, health and safety information, read the product's Technical Data Sheet and Safety Data Sheet (SDS) from the documents section.

 

 

 

Documents
TDS

Technical Data Sheet

SDS

Safety Data Sheet

EN71-3

Toy Safety Certificate

Tips
  • If you are going to apply with a roller, pour the amount of product you will use into a container where your roll can fit. Make sure that the container is dry and clean.
  • Start the application from the edges with the brush.
  • Do not sweep too much in order to leave enough product on the surface.
  • The brush or roller to be used in the applications must be saturated with the product before starting the application. After this process, the excess product left on the roll or brush should be removed by rubbing on the edge of the package or using a suitable apparatus. Thus, in the first applications, a sufficient amount of varnish will be applied to the surface.
  • When applying the first coat, it is important to apply the varnish to the parquet surface first transversely, then longitudinally, without too much sweeping, to apply equal and sufficient amount of varnish to the surface.
  • 7 days should be waited for carpet laying or cleaning.
TOP