Prime Parquet Varnish 2K

Surface Preparation:

Do not use products like cellulose or polyurethane filler or primer before the application ofthe product. As a filler, mix the wood dust with the product and fill all gaps and joints of theparquet. Clean the excess paste after it has dried out.

New Wood Surfaces:

• Remove any dirt, oil, and wood dust from the surface.
• Sand the surface with parquet sanding machine or hand using sandpaper #120/150. 
• Thoroughly clean the generated dust and remove it completely from the surface witha vacuum cleaner.
• Prime Decorative Colorant can be used for coloring the parquet floor. After thecoloring, allow at least 6 hours to dry before varnish application.
• Cila uygulamasına başlamadan önce, uygulanan rengin kuruması için en az 6 saat bekleyin.
  Varnished Wooden Floors: 
• Remove the old varnish from the parquet completely with a scraping machine. Remove any dirt, oil, wood dust and old varnish residues from the surface. 
• Thoroughly clean the generated dust and remove it completely from the surface witha vacuum cleaner.
• Thoroughly clean the generated dust and remove it completely from the surface witha vacuum cleaner.
• Remove the remaining dust with a damp cloth.

Application:

• The product is ready to use and does not require thinning. (At very high temperatures 2-3%drinking water may be added). 
• Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application. 
• Add the hardener at a rate of 10% while mixing the varnish with a spatula or stick. Do not stir too fast; the hardener should be added slowly. The container used must be dry and clean. Mixing process should be completed after the hardener is added and allowed to rest for 10 minutes before application. The mixture should be as follows applied within 5 hours.
• Apply the 1st coat by a brush or roller and leave it to dry for 2 hours. 
• Perform a slight sanding with sandpaper #180/220 before applying 2nd coat 
• Apply the 2nd and 3rd coats in 2 hours intervals by sanding with sandpaper #180/220 between the coats.
• For any reason, if 8 hours exceeded between coats, wait 24 hours and sand the surface with sandpaper #220/240 (aluminum oxide or silicon carbide type sandpaper is recommended) before applying the next coat.
• Apply the 1st varnish coat first across the grain and then along the grain to leave equal and sufficient amount on parquet surface without sweeping too much.
• The area should be ventilated after the application to promote the drying.
• Allow 7 days for full cure.
• .

Instructions:

• Do not apply the product directly to polished surfaces.
• Remove the old varnish from the parquet completely with a scraping machine. Remove any dirt, oil, wood dust and old varnish residues from the surface.
• Thoroughly clean the generated dust and remove it completely from the surface witha vacuum cleaner.
• Remove the remaining dust with a damp cloth. 
• Repeat same process as described in “Application” with 3 coats. 
• Inspect annually and maintain as required.

Instructions:

• FOR INTERIOR USE ONLY.
• Do not apply products such as nitro, polyurethane basecoats or primers before PrimeParquet Varnish. 
• Keep product closed when not in use. 
• The general application temperature of the product is between 15oC to 25oC at a relativehumidity range of 40-65%. 
• The moisture content of the wood should be below 12%. 
• The area should be ventilated during and after the application to promote the drying. 
• The product should not be applied when the weather or surface temperature is below 10°C. 
• The varnished floor should not be cleaned with ammonia containing cleaning materials. 
• The varnished floor can be stepped on after 24 hours. Allow 7 days before spreading carpetand/or cleaning. 
• The product should be protected from freezing and stored at temperatures between 5°C to35°C. 
• Painting tools should be cleaned with soap and plenty of warm water after application.